Repair & maintenance guides

How to Mount Rod Holders, Fish Finders, Cleats and Antennas Without Causing Leaks

Add accessories to your boat the right way, with through-bolts, backing plates, sealed core and proper wire pass-throughs, so every new hole stays dry and strong. Also learn where you should never drill.

How to Paint a Boat Bilge (Prep, Paint Choice and What to Leave Bare)

A freshly painted bilge is easier to keep clean and makes small fuel, oil, coolant and water leaks easy to spot. Learn how to degrease and sand, pick between alkyd bilge paint and epoxy coatings, ventilate safely, and keep paint off the parts that must stay bare.

How to Paint Your Boat's Topsides (Roll and Tip)

When the gelcoat above the waterline is too chalky or crazed to polish back, a one-part or two-part polyurethane paint can bring back the shine. This guide covers choosing the paint, prep, weather windows, roll-and-tip technique and the safety gear two-part paints demand.

How to Prevent and Remove Mold and Mildew on Your Boat

Stop the musty smell and black spots before they start. Find and fix the water source, keep air moving, control humidity safely, and clean mold off gelcoat, vinyl and cabin surfaces with products that won't damage them.

How to Re-Cover Boat Cushions and Seats (DIY Sewing vs. Upholstery Shop)

Cracked, faded or split cushion covers can be replaced without buying new seats. Learn how to choose marine vinyl or acrylic fabric, which thread survives the sun, how to use the old cover as a pattern, where zippers and drain vents go, and when a walking-foot machine at home makes sense versus paying an upholstery shop.

How to Remove and Apply Boat Names, Graphics and Registration Decals

Take off old vinyl names and graphics without scratching the gelcoat, clean up the glue and the "ghost" outline, then apply new lettering straight and bubble-free, and display your registration numbers the way federal rules require.

How to Repair or Repaint Worn and Cracked Non-Skid Decks

Bring back grip where the molded non-skid is chipped, cracked, patched or worn smooth. Choose between a molded patch that copies the original pattern, non-skid paint with grit, or textured gelcoat, fix the cracks and soft spots underneath first, and mask for clean, safe edges.

How to Repair or Replace Your Boat's Rub Rail

Replace a torn rub rail insert or the whole rail, reseal the hull-to-deck joint and its fasteners while the rail is off, and stop the deck-joint leaks that often hide behind a worn rail.

How to Repair Small Gelcoat Chips and Scratches

Fill and blend small chips, dings and scratches in your boat's gelcoat with a repair kit so they stop letting water into the fiberglass and look close to new. Also learn to spot damage that is structural and needs a pro.

How to Repair Torn-Out Canvas Snaps, Fasteners and Zippers

Fix snaps that have pulled out of your bimini, cover or enclosure, reinforce the torn fabric, choose the right snap metal and setting tool, free stuck snaps, replace Lift-the-Dot and twist fasteners, and swap a worn zipper slider.

How to Replace Cleats, Eyes and Brackets on a Riveted Aluminum Boat

Swap or add cleats, tie-down eyes, rod holders and accessory brackets on an aluminum boat without starting corrosion or new leaks. The keys are isolating stainless from aluminum, picking the right rivet or bolt, and spreading the load.

How to Replace Gas Struts on Boat Hatches, Seats and Consoles

Measure, buy and fit the right gas struts (lift supports) so hatches, seat lids and console doors stay open safely instead of dropping on your head or fingers.

How to Replace or Re-Cover a Bimini Top

Decide whether you need new canvas or a whole new top, measure your frame the right way, pick a fabric that will last in the sun, check the frame and hardware, and swap the canvas yourself or brief a canvas shop.

How to Test and Clean Your Bilge Pump and Float Switch

Make sure your bilge pump actually moves water overboard, both on the manual switch and automatically through the float switch. A working bilge pump is one of the most important safety systems on any boat that stays in the water.

How to Touch Up Paint and Corrosion on an Outboard or Sterndrive

Bare aluminum on a lower unit or sterndrive corrodes fast, especially in salt water. Learn how to find the cause, clean off corrosion, prime and repaint with the right products, and what must never be painted, such as anodes and sensors.

Hull Blisters (Osmosis): How to Tell Cosmetic Pimples From Serious Pox

Learn what osmotic blisters are, how to inspect a fiberglass bottom at haul-out, which blisters you can fix yourself with epoxy, what moisture meter readings can and can't tell you, and when to hire an independent surveyor.

Hull Potential Survey: Checking Corrosion Protection with a Reference Electrode

A silver/silver-chloride reference electrode and an ordinary multimeter show whether your underwater metals are really protected by their anodes, whether every fitting is bonded, and whether shore power or the slip is upsetting things. Learn how to take the readings, what under- and over-protection mean in plain terms, and when to call a marine electrician or corrosion specialist.

Hydraulic Steering: Check Fluid, Bleed Air and Fix Stiff or Loose Steering

Check the fluid in your hydraulic steering helm, bleed out the air that makes steering spongy, and track down the usual causes of stiff, loose or noisy steering. Includes notes for boats with mechanical cable steering.

Inboard and Sterndrive Engine Mounts: Signs of Failure and How to Inspect Them

The rubber mounts under an inboard or sterndrive engine soak up vibration and hold the engine in line with the drive. Learn the warning signs of a failing mount, how to inspect all of them in under an hour, and why a mount replacement always ends with an alignment check.

Inflatable Boat and Dinghy Care: Cleaning, UV Protection, Leaks and Storage

Keep your inflatable or RIB tender holding air for years. Rinse and clean it the right way, protect the tubes from sun, check pressure with a gauge, find slow leaks with soapy water, service the valves, patch small holes with the correct glue for PVC or Hypalon, and store it clean and dry.

Livewell, Baitwell and Washdown Pumps - Clean, Troubleshoot and Winterize

Find out why a livewell or washdown pump runs but moves no water, from a closed valve or clogged pickup to an airlock, then clean the system and winterize both sides of every pump so nothing cracks over the winter.

Marine Head and Holding Tank Care: Odors, Clogs, Pump-Outs and Winterizing

Keep your boat's toilet and holding tank working and odor-free, clear common clogs, pump out the right way, and winterize the system. Also covers the Y-valve and the federal no-discharge rules every owner with a head needs to follow.

Marine Sealants Explained: 5200, 4200, 4000UV, Polysulfide, Silicone and Butyl Tape

Pick the right sealant before you bed a cleat, a through-hull, a window or a transducer. The wrong goo either leaks in a year or glues a part on so hard you damage the boat getting it off.

Marine Vinyl Stain Removal: Ink, Sunscreen, Grease, Mildew and Pink Stain

A stain-by-stain plan for boat seat vinyl that follows your vinyl maker's own cleaning list, starts with the mildest method, and keeps you away from the products that strip the protective top coat, rot the stitching or crack the vinyl.