Repair & maintenance guides

How to Prevent and Remove Mold and Mildew on Your Boat

Stop the musty smell and black spots before they start. Find and fix the water source, keep air moving, control humidity safely, and clean mold off gelcoat, vinyl and cabin surfaces with products that won't damage them.

How to Protect Your Boat, Motor and Trailer From Theft

Practical, layered security for boat owners: outboard locks, trailer coupler and wheel locks, disabling the boat, GPS trackers, engraving and marking, photo and serial number records, safer storage, and exactly what to report (HIN and serial numbers) if your boat is stolen.

How to Re-Cover Boat Cushions and Seats (DIY Sewing vs. Upholstery Shop)

Cracked, faded or split cushion covers can be replaced without buying new seats. Learn how to choose marine vinyl or acrylic fabric, which thread survives the sun, how to use the old cover as a pattern, where zippers and drain vents go, and when a walking-foot machine at home makes sense versus paying an upholstery shop.

How to Read Buoys and Channel Markers: Red Right Returning and the U.S. Aids to Navigation System

Learn what the red and green buoys, daymarks and lights are telling you: red right returning, nuns and cans, odd and even numbers, preferred channel, safe water, isolated danger, the orange-and-white regulatory and information markers, the yellow symbols on the Intracoastal Waterway and how the Western Rivers system differs. Based on the Coast Guard's U.S. Aids to Navigation System rules (33 CFR Part 62).

How to Refuel a Boat Safely (Gas Dock, Gas Station and Portable Tanks)

A step-by-step fueling routine that keeps gasoline vapor out of your bilge and fuel out of the water: shut everything down, close up, keep the nozzle in contact, stop short of full, ventilate, run the blower and sniff before you start. Includes portable tanks, personal watercraft and what to do about a spill.

How to Remove and Apply Boat Names, Graphics and Registration Decals

Take off old vinyl names and graphics without scratching the gelcoat, clean up the glue and the "ghost" outline, then apply new lettering straight and bubble-free, and display your registration numbers the way federal rules require.

How to Repair or Repaint Worn and Cracked Non-Skid Decks

Bring back grip where the molded non-skid is chipped, cracked, patched or worn smooth. Choose between a molded patch that copies the original pattern, non-skid paint with grit, or textured gelcoat, fix the cracks and soft spots underneath first, and mask for clean, safe edges.

How to Repair or Replace Vinyl Flooring on a Pontoon or Bowrider

Fix small tears, lifted seams and bubbles in marine vinyl or woven vinyl flooring with the right adhesive, tell when a soft spot means the plywood underneath is rotting, and understand what a full floor replacement involves. Structural deck and stringer repairs are pro work.

How to Repair or Replace Your Boat's Rub Rail

Replace a torn rub rail insert or the whole rail, reseal the hull-to-deck joint and its fasteners while the rail is off, and stop the deck-joint leaks that often hide behind a worn rail.

How to Repair Small Gelcoat Chips and Scratches

Fill and blend small chips, dings and scratches in your boat's gelcoat with a repair kit so they stop letting water into the fiberglass and look close to new. Also learn to spot damage that is structural and needs a pro.

How to Repair Torn-Out Canvas Snaps, Fasteners and Zippers

Fix snaps that have pulled out of your bimini, cover or enclosure, reinforce the torn fabric, choose the right snap metal and setting tool, free stuck snaps, replace Lift-the-Dot and twist fasteners, and swap a worn zipper slider.

How to Replace Boat Battery Cables the Right Way

Swap corroded, cracked or undersized battery cables for tinned marine cable sized from a chart for its real length and load, with crimped lugs, adhesive heat shrink, terminal boots, solid support and a fuse close to the battery.

How to Replace Cleats, Eyes and Brackets on a Riveted Aluminum Boat

Swap or add cleats, tie-down eyes, rod holders and accessory brackets on an aluminum boat without starting corrosion or new leaks. The keys are isolating stainless from aluminum, picking the right rivet or bolt, and spreading the load.

How to Replace Folding Boat Seat Hinges and Fix Back-to-Back Seats

Fix flip-up seats, fold-down fishing seats and back-to-back lounge seats that sag, jam or rip loose. Replace rusted or bent hinges with stainless hardware, rebuild a rotten plywood base so the new screws actually hold, and adjust the latches so the seat stays put.

How to Replace Gas Struts on Boat Hatches, Seats and Consoles

Measure, buy and fit the right gas struts (lift supports) so hatches, seat lids and console doors stay open safely instead of dropping on your head or fingers.

How to Replace Marine Speakers (Including Tower Speakers)

Pick replacement speakers that fit the cutout, match your stereo or amplifier's power and impedance, survive sun and spray, and don't throw off your compass. Then wire them with the right polarity and seal them so water can't reach the back.

How to Replace or Re-Cover a Bimini Top

Decide whether you need new canvas or a whole new top, measure your frame the right way, pick a fabric that will last in the sun, check the frame and hardware, and swap the canvas yourself or brief a canvas shop.

How to Run New Wires Through a Boat (Chase Tubes, Pull Lines and Deck Penetrations)

Get a new transducer cable, light or power wire from the stern to the helm or up through the deck without a fight: use the chase tube and a fish tape or pull string, protect the wire from chafe and heat, support it every 18 inches, seal every penetration and label both ends.

How to Size a House Battery Bank: Load List, Usable Capacity and Charging

Work out how many amp-hours your boat really uses in a day, how much of a battery's rated capacity you can actually use with lead-acid, AGM or lithium, how much reserve to add, and how your charging sources change the answer, so you buy the right house bank the first time.

How to Size, Rig and Inspect Dock Lines and Fenders

Pick the right dock line diameter and fender size for your boat, set up bow, stern and spring lines in a slip, add chafe gear, inspect for wear and UV damage, and double everything up before a storm.

How to Tell if Your Boat's Flotation Foam Is Waterlogged

Learn the signs that the foam under the floor or seats of a small boat has soaked up water, how to check without tearing the boat apart, what the Coast Guard flotation rules mean for you, and why replacing foam is usually a big job for a pro.

How to Test and Clean Your Bilge Pump and Float Switch

Make sure your bilge pump actually moves water overboard, both on the manual switch and automatically through the float switch. A working bilge pump is one of the most important safety systems on any boat that stays in the water.

How to Test and Fix Your Boat's Navigation Lights

Learn which navigation lights your boat must show and when, then test them and fix the usual culprits such as corroded sockets, loose pole-light plugs and blown bulbs. Working lights are legally required at night and in poor visibility and are how other boats see which way you are heading.

How to Upgrade Your Boat's Lighting to LED (and Keep Your Nav Lights Legal)

Switch cabin, cockpit and courtesy lights to LED to cut battery drain and bulb changes, choose navigation lights that are actually USCG-certified (not just LED bulbs), check voltage range and dimmers, seal every connection, and run the Coast Guard's simple VHF test to make sure the new lights aren't deafening your radio or AIS.