Repair & maintenance guides

NMEA 2000 Network Basics and Troubleshooting (Plus Chartplotter Updates)

Understand the backbone, terminators, power tap and drop cables that tie your chartplotter, engine data, GPS, depth and autopilot together, then track down why a device keeps dropping off. Finish by updating chartplotter and device software the safe way.

Powering a Big Boat Sound System: Amplifier Draw, an Audio Battery and Charging

Work out how much current your amplifiers really pull, size a dedicated audio battery, keep it charged with an automatic charging relay or isolator, and fuse and wire it so a long day of music never leaves you unable to start the engine.

Recreational Radar Care: Radome and Open-Array Cleaning, Mounts, Cables and Alignment

Keep your boat's radar seeing small targets by cleaning the radome or open array the right way, checking the mount, cable and connectors for corrosion, and confirming that targets line up with the bow. Includes the safety rules for working near a radar that might transmit, plus winter care.

Remote Boat Monitoring: Bilge, Battery, Shore Power and GPS Alerts on Your Phone

Choose, install and set up a system that texts you when your unattended boat is taking on water, losing battery or shore power, or moving without you. Covers cellular versus satellite, what each sensor really tells you, wiring it so it stays on, sensible alert settings and what happens to your location data.

Running a Boat Generator at the Right Load: Switching Sequence, Balancing and Avoiding Wet Stacking

Get more life out of your marine generator by starting and stopping it with the AC loads off, switching sources in the right order, keeping it loaded enough to avoid wet stacking and carbon buildup, and moving small loads to the inverter. Includes a simple monthly exercise routine.

Satellite Internet on Your Boat: Starlink Plans, Mounting, Power and Wiring

An owner's guide to putting Starlink aboard: which plans allow coastal, offshore and in-motion use (as of October 2026), how much battery it eats, 12-volt versus inverter power, where to mount the dish, and how to route and seal the cable without leaks.

Shore Power Adapters and Y-Splitters: When a 30A or 50A Adapter Is Safe, and When It Isn't

Pigtail adapters and Y-splitters let a boat plug into a pedestal that doesn't match its inlet, but the wrong one, or the right one used carelessly, can overheat, trip the marina's ground-fault protection or start a fire. Learn the difference between 30A 125V, 50A 125V and 50A 125/250V, which adapters are reasonable, how to keep loads safe, and how to check connections for heat.

Shore Power Cord Ends: How to Judge a Cord, and When to Replace the Plug or the Whole Cord

Burned blades, a hot plug or a cracked locking ring don't always mean a brand-new cord, but sometimes they do. Learn how to inspect a shore power cord and its ends, decide between a replacement end and a new cord, what a proper sealed marine connector looks like, which parts of the job are safe for an owner and when the work belongs to an ABYC-certified electrician, plus the habits that make cord ends last.

Shore Power Inlet and Cord Upgrades: Burned Plugs, Better Connectors and Safe Adapters

Why shore power plugs and boat inlets overheat and burn, how to spot an inlet that needs replacing, what newer connector designs offer, and how to choose, size and care for cords and adapters. You inspect and buy the right cord; an ABYC-certified marine electrician replaces the inlet and its wiring.

Shore Power Safety: Cords, Inlets, Burned Plugs and Electric Shock Drowning

An owner's inspection routine for your shore power cord, plugs, boat inlet, galvanic isolator and ground-fault protection, plus the right way to plug in and the facts about Electric Shock Drowning. This guide is for looking and testing only; any electrical repair belongs to an ABYC-certified marine electrician.

Start Isolation for Your ACR: Stop the Chartplotter and Stereo from Rebooting at Engine Start

If your plotter, radio or stereo reboots every time you turn the key even though you have two batteries and an automatic charging relay, the relay may be tying the house battery into the cranking dip. Learn how start isolation and dual-circuit battery switches keep the electronics on their own battery, how to find and test the start-only wire, and what to check after the job.

Switching to Lithium (LiFePO4) Boat Batteries: What Changes and When It's Worth It

What really changes when you swap lead-acid for lithium iron phosphate (LiFePO4) batteries on a boat: the battery management system, charger settings, protecting the alternator with a DC-DC charger, not mixing chemistries, cold-weather charging, and which jobs (trolling, house, starting) suit lithium. House-bank conversions should be designed and installed by a qualified marine electrician.

Testing Your VHF Antenna and Coax: Radio Checks, SWR, Connectors and Mounts

Most weak or scratchy VHF radios have nothing wrong with the radio. Learn how to test the whole antenna system, from a proper radio check and a DSC test call to a multimeter and SWR meter, how to find corroded connectors and wet coax, and when to replace the cable, antenna or mount.

Underwater LED Lights: Care, Leaks, Corrosion, Wiring and the Rules

Keep underwater LED lights bright and your hull dry. Learn the difference between through-hull and surface-mount lights, how to clean growth off the lens without damaging it, what to check for leaks, wiring, fusing and bonding, when the boat has to be hauled, and why the lights should not be on while you're underway.